故障
Malfunction | 原因
Causes | 措施
Measures |
在減速機的緊固件處有大的噪聲
High noise at tightening parts | 緊固件松動了
Loose of tightening parts | 將螺栓/螺母擰緊到規定的扭矩。更換損壞了的螺栓/螺母。
Tighten nut bolt to correct state Replace damaged nut/bolt |
減速機的噪聲變化
Changing noise | 齒輪的輪齒發生了損壞
Teeth of gears get damaged | 和客戶服務部聯系。檢查所有零件上的齒，更換損壞了的零件。
Consult after-sales department
Check teeth of gears and replace damaged one. |
軸承間隙過大
Clearance of bearings too big | 和售后服務部聯系。
調整軸承的間隙。
Consult after-sales department
Adjust the clearance of bearings |
軸承損壞
Bearings get damaged | 和客戶服務部聯系。
更換損壞的軸承。
Consult after-sales department
Replace damaged bearings |
軸承溫度升高
Bearing temperature rise | 箱體里面的油面過高或過低
Oillevel is too high or low | 在室溫下檢查油面的高度并按需加油。
Check oil level at room temperature and add on reduce oil |
油過于陳舊
Oil is used too long | 和售后服務部聯系。
檢查上次換油的時間。
Consult after-sales department.
Check the date that oil be replaced last time. |
油泵的機械故障
Malfunction of oil pump | 和售后服務部聯系。
檢查油泵的工作是否正常，修理或換新的油泵。
Consult after-sales department.
Check if pump works normally,repair or replace it. |
軸承損壞
Bearing damage | 和售后服務部聯系。
-查閱操作人員在振動測量中所獲得的數據。
-檢查并按需要換軸承。
Consult after-sales department.
-Look up the date about vibration.
-Check and replace it on request. |
工作溫度過高
Working temperature too high | 箱體里面的油面過高
Oil level is too high | 檢查油面的高度，如果有必要的話，調整。
Check oil level,and adjust if necessary. |
油過于陳舊
Oil is used too long | 和售后服務部聯系。
檢查上一次換油的時間，如果有必要的話就更換。
Consult after-sales department.
Check the date that oil was replaced last time,
replace it if necessary |
油受到嚴重污染
Oil is pollucted seriously | 和售后服務部聯系
-換油。
Consult after-sales department.
-Replace oil. |
在配備了潤滑油冷卻系統的減速機上：冷卻劑的流量過低或者過高
Flux of cooling material is too high or low | 全面調節進口和出口管道的閥門。
檢查水冷裝置的自由流量。
Adjust entrance and exit valves.
Check the flux of water cooling devices. |
通過水冷裝置的油流過低，其原因是：濾油器嚴重堵塞
Oil flux through water cooling devices is too low | 清理濾油器
Clean oil filter |
油泵的機械故障
油泵損壞
Malfunction of oil pump
Oil pump damage | 和售后服務部聯系。
-檢查油泵的功能是否正常。
-修理或者換新。
Consult after-sales department.
-Check of oil pump works normally.
-Repair or replace it. |
在配備了風扇的減速機上：風扇罩的空氣入口和/或箱體嚴重污染
Entrance of fan shield and housing polluted seriously | 清理風扇罩和箱體
Cleanse fan shield and housing. |
配備了冷卻螺旋管的減速機：冷卻螺旋管里面結垢
Redsidues in cooling coil | 和售后服務部聯系。
-清理或者更換螺旋管。
Consult after-sales department.
-Claen or replace cooling coil. |
軸承處的振幅升高
Swing at bearing higher | 軸承損壞
Bearing is damaged | 和售后服務部聯系。
-檢查并按需更換軸承。
Consult after-sales department
-Check and replace bearing. |
齒輪損壞
Gear is damaged | 和售后服務部聯系。
-檢查并按需更換齒輪。
Consult after-sales department.
-Check and replaces gears. |
止回裝置的溫度過高
止回功能的失效
Temperature of anti-backstop too high and it becomes malfunction | 止回裝置損壞
Anti-backstop becomes malfunction | 和售后服務部聯系。
-檢查并按需更換止回裝置。
Consult after-sales department.
-Replace anti-backstop |
減速機漏油
Oil-leak of gear unit | 箱體蓋或者聯接處的密封不良
Sealing at cover and connection not in good state | 檢查密封和連接處，如果必要的話，更換新的。將連接處密封好。
Check air-proof and connection part,replace them if necessary,and seal up connection part. |
徑向軸封失效
Shaft seal is malfunction | 和售后服務部聯系。
-換新的徑向密封環。
Consult after-sales department. |
油中有水
Water in oil | 油中有雜物
Mixer in oil | 用試管檢查油的狀態是否有水分存在。
實驗室分析油.
Classify if there is water in oil by using tube.
Analyse oil in laboratory. |
潤滑油冷卻器或者冷卻螺旋管失效。
Cooling coil is of mal-fanction | 和售后服務部聯系。
-找出并修理泄漏之處。
-更換冷卻器或者螺旋管。
Consult after-sales department.
-Find out and repair leakage place.
-replace cooling coil |
減速機受到機器間通風過來的涼空氣而產生凝露
Cool air will cause water drop in gear unit. | 用合適的保溫材料將減速機保護起來。
關閉空氣的出口或者在結構上改變其方向。
Shelter gear units with proper |
關注官方微信
